| SKF
Induction Heater Model TIH 030m |
|
A |
Induction coil
outside the heater's housing allows shorter heating time and
lower energy consumption |
|
B |
Foldable bearing
support arms facilitate the heating of larger diameter
bearings |
|
C |
Magnetic
temperature probe helps prevent bearing overheating |
|
D |
Easy-to-use
control panel and LED display integrated in a remote control |
|
E |
Internal storage
for all 3 yokes reduces the risk of yoke damage or loss |
|
F |
Integrated
carrying handle facilitates portability |
Buy Now
SKF
Bearing Heater |
Small bearing heater with high heating
capacity of up to 88 lb bearing
SKF TIH 030m combines high heating capacity with portability. The
compact lightweight design makes the TIH 030m portable. Placing the
induction coil outside the heater's housing allows the heating of
bearings weighing up to 88 lb (40 kg). The heater is equipped with
thermal overheating protection to reduce the risk of damage to the
induction coil and the electronics. In addition to temperature mode,
the TIH 030m is equipped with a time mode for heating components
other than bearings. The heater is supplied standard with three
yokes. Power is 100-110V/50-60Hz.
Features:
Compact lightweight design 46 lb (20,9 kg)
2-step power setting and smaller yokes allow heating smaller
bearings safely and at lower power consumption
Capable of heating a 61.7 lb (28 kg) bearing in just 20 minutes
Temperature mode pre-set at 110 °C (230 °F) to help prevent bearing
over-heating
Automatic demagnetization
3 years warranty
Specifications subject to change without Notice.
SKF m20 concept
"m20" represents the weight (kg) of the heaviest SRB 231
bearing which can be heated from 20 to 110 °C (68 to 230 °F) in 20
minutes. This defines the heater's power output instead of its power
consumption. |
| SKF Electric
Hot Plate for Small Bearings |
SKF High
Frequency Induction Bearing Heater |
|
 |
  |
Thermostat controlled bearing
heating
The SKF electric hot plate, 729659 C, is a professional
heating device especially designed for pre-heating small bearings
prior to mounting. The temperature of the plate can be adjusted at
the turn of a knob to provide a temperature range of between 50 and
200 °C (120 and 390 °F). Protective cover to avoid contamination
during heating.
Technical data
Designation: 729659 C/110V
Voltage: 115V (50/60Hz)
Power: 1.000 W
Temperature range: 50°-200°C (120°-390°F)
Plate dimensions: (l x w) 380 x 178 mm (15 x 7 in)
Height of cover: 50 mm (2 in)
Overall dimensions: (l x w x d) 400 x 240 x 130 mm (16 x 10 x 5 in)
Weight: 4,7 kg (10 lb)
Length of connection cable: 2 meters (6.6 ft) (earth connection
required)
Specification Subject to change without notice. |
The SKF Bearing Heater TMBH 1
A portable bearing heater weighing only 10 lb1 The Scorpio is a
portable lightweight heater for heating bearings with an inner
diameter ranging from 20 to 100 mm (0.8 to 4 in) and a maximum
corresponding weight of 10 lb. The heater uses a patented method of
heating based on high frequency induction, which provides optimized
efficiency. This method is very quiet and creates no magnetization
at all. In addition to bearings, the heater can also be used for
heating ferrous components such as gears, pulleys, bushings and
shrink rings.
Heating efficiency better than 85%
Components are not magnetized
Equipped with temperature and time control
Supplied with a heating clamp, temperature probe, power cable, heat
resistant gloves and a carrying case.
Specifications subject to change without Notice.
|
|
Buy Now
SKF Bearing Hot Plate |
Buy Now
SKF Bearing Heater |
e-mail us
YOUR
SOURCE FOR PRECISION MAINTENANCE TECHNOLOGY
Tel:
603-714-4324 (USA)
